A bound catalogue, magazine or book is ready for print when it meets these conditions:
- The binding is chosen before layout: it decides how many pages it can have, the inside margin and what the cover is like.
- When saddle-stitched, the page count is a multiple of 4, including blank pages.
- With a glued (PUR) or sewn spine, the inside margin is wider: part of the page ends up inside the spine.
- Nothing important crosses the centre of a spread, except on the centre pages of a saddle-stitched job.
- The inner pages go in a PDF of single pages, in reading order, with 3 mm bleed on all four sides.
- The cover goes in a separate PDF, laid out flat in one piece with back cover, spine and front cover.
- The spine depends on the pages, the paper and the binding: ask us for its width before finalising the cover.
The rest of the file follows the usual rules: bleed, safe area, CMYK, resolution and fonts. They are in the guide How to prepare a file for printing. Here we explain only what changes when the piece has many pages and is bound.
1. Which binding should I choose for a catalogue?
The one that fits the page count and how it will be used. A catalogue consulted at a counter, a magazine handed out at a trade fair and a book that has to last for years do not need the same thing. And each method changes something in the file, so it is best to decide before you start the layout.
| Binding | What it is | What it is for | What changes in the file |
|---|---|---|---|
| Saddle-stitched | Sheets folded in half, one inside the other, and stapled along the fold | Catalogues and magazines with few pages, quick guides, price lists | Pages in multiples of 4; the cover has no spine |
| PUR binding | Sheets glued at the spine, with a soft cover wrapped around them | General catalogues and magazines with many pages; the spine can carry a title | Wider inside margin; cover with spine |
| Sewn | Signatures sewn with thread, with a soft or hard cover | Books and catalogues that get heavy use: more durable and opens better | Wider inside margin; cover with spine; page count matched to the signatures |
| Wire-o | Sheets punched along the edge and joined with a double metal loop | Reference catalogues, manuals and price lists: opens fully and lies flat | Clear strip for the holes; no spine |
| Concealed wire-o | Wire-o with a cover that wraps around the loop and forms a spine | The practicality of wire-o with the presence of a titled spine | Clear strip for the holes; cover with spine |
| Hardcover | Board cover wrapped in the printed paper, joined to the inner pages with endpapers | Presentation books and catalogues that have to last | The cover wraps around the board and needs extra margin; endpapers supplied separately |
Any of them can take extras: flaps on the cover, printed endpapers and headbands on hardcovers, or an elastic band to keep it closed. We show them in Finishes. If you are torn between two methods, tell us how many pages it has and how it will be used, and we will work it out with you.
2. How many pages can a catalogue have?
When saddle-stitched, a multiple of 4: 8, 12, 16, 20, 24… Each sheet is folded in half and gives four pages, so there is no other way to make it up.
- Blank pages count. If the inside front cover is blank, that is one more page. Include them in the PDF, in their place.
- The cover counts too if it is stapled with the inner pages: that is four pages (front cover, inside front cover, inside back cover and back cover).
- With any binding the total is even, because each sheet has two sides.
- With sewn binding, the inner pages are made up in signatures, so the page count also has to match them. Ask us how many fit before you finalise the layout.
- Saddle stitching has a limit. With many pages or thick paper, the catalogue does not close properly and it is better to move to PUR binding or wire-o. Where the limit lies depends on the paper: ask us.
Example. A saddle-stitched product catalogue comes out at 30 pages of content. It cannot be made up: either 2 pages come out (28) or 2 go in (32), for example an index page and a contact page. If it stays at 30, two blank pages will have to be added, and perhaps not where you would want them.
In saddle-stitched catalogues with many pages, the centre sheets sit slightly further out than the outer ones and, when trimmed, lose a little more along the outer edge. Keeping to the 3-5 mm safe area from the trim line stops it from showing.
3. What inside margin does a bound catalogue need?
Wider than the outside margin if it has a PUR or sewn spine, because part of the page ends up inside the spine and cannot be seen when it is opened. The more pages it has, the less it opens and the more of the page is hidden.
- PUR and sewn spines: make the inside margin wider than the outside one. Text or a table close to the centre ends up buried in the spine, and the catalogue has to be forced open to read it.
- Wire-o: leave the strip along the edge where the holes go clear. Anything there disappears into the holes.
- Saddle-stitched: opens almost flat and needs less inside margin than PUR or sewn binding.
- Outside, top and bottom margins: the usual safe area, at least 3-5 mm from the trim line, as we explain in the file preparation guide.
How much wider the inside margin needs to be depends on the page count, the paper and the binding. If your catalogue has many pages, ask us before you set the grid.
4. Can I run an image or text across a spread?
An image, yes, if there is nothing important in the centre. Text or data that crosses the centre, no: with a PUR or sewn spine part of it ends up inside the spine, and with wire-o the loop cuts through it.
- Images: place the important part (a face, a product, a logo) away from the centre. Whatever falls into the fold will be lost or distorted.
- Text and tables: never across the centre. A table of product codes and prices split across two pages is the quickest way for someone to misread a figure.
- Saddle-stitched: the centre spread is the only one that is continuous, because it is a single sheet. It is the place for a map, a full product range or a large photo. On the other spreads, each half is on a different sheet and a slight misalignment may show.
- Set up spreads as two single pages in the PDF, each with its own half. There is no need to impose them.
5. Where do I put the page numbers?
Inside the safe area, like any other text: at least 3-5 mm from the trim line. A page number right at the edge can get trimmed off.
- On the outer side or centred is better than next to the spine: that is where people look for them when flicking through, and where they are not hidden.
- Odd pages go on the right. The first page of the inner pages is a right-hand page. If you number by hand, check that the odd pages are on the right.
- The contents page has to match the page numbers in the final PDF. If you add or remove pages to reach a multiple of 4, check the contents page afterwards.
6. How do I supply the inner pages and the cover?
In two PDFs: one with the inner pages as single pages and another with the cover. The inner pages and the cover are usually on different papers and are prepared separately.
The inner pages
- Single pages in reading order, not spreads or imposed sheets. You do not have to do the imposition (the order in which pages are placed on each sheet).
- 3 mm bleed on all four sides of every page, including the spine side, and crop marks.
- With blank pages in their place. Do not remove them from the PDF.
- Without the cover, unless it is saddle-stitched and on the same paper as the inner pages: in that case, ask us how you would rather send it.
The cover
- With a spine (PUR, sewn, concealed wire-o, hardcover): a single flat piece with back cover, spine and front cover, from left to right, with 3 mm bleed all round. If the inside of the cover is printed, add a second page with that side.
- Without a spine (saddle-stitched, wire-o): the four sides of the cover: front cover, inside front cover, inside back cover and back cover.
- Flaps: go in the same file as the cover, at the sides. Ask us for the measurements before designing.
- Hardcover: the cover wraps around the board and needs an extra margin all round to fold over on the inside. Endpapers, if printed, are sent in a separate file. Ask us for the measurements before designing the cover.
- Varnish or foil stamping on the front cover: these go on their own layers and at least 3 mm from the trim line and from the spine folds. We explain this in the spot UV varnish and foil stamping guide.
How to export it from InDesign
- Check in File → Document Setup that Facing Pages is turned on. That way the margins become “Inside” and “Outside”.
- Set the wider inside margin in Layout → Margins and Columns.
- Export with File → Export → Adobe PDF (Print) and, under General, select Export As: Pages, not Spreads.
- Under Marks and Bleeds, turn on crop marks and the document bleed (3 mm).
If you lay it out in Canva: each Canva page is one page of the catalogue. Do not build spreads on a single page; download it as a print PDF with crop marks and bleed, as we explain in the file preparation guide.
7. How wide is the spine?
It depends on the page count, the paper and the binding, so there is no fixed measurement: ask us for the spine width before finalising the cover.
- Page count: every sheet adds thickness. Two pages more or fewer already change the spine.
- Paper: two papers of the same weight can have different thicknesses. Uncoated offset paper is bulkier than coated paper of the same weight.
- Binding: the glue, the thread of the signatures or the board of a hardcover also add to it.
That is why the cover is the last thing to be finalised. If you design before you have the width, leave the spine as a strip that can be adjusted and do not tie the front or back cover to a specific measurement. If the spine is narrow, the text may not fit: ask us before putting a title on it.
Example. A medical supplies distributor reprints its catalogue in PUR binding every year. This year it adds a product family and goes from 96 to 112 pages. The front and back covers do not change, but the spine does: the new width has to be requested and the cover adjusted. Reusing last year's cover leaves the spine title off-centre or running onto the front cover.
8. What changes when updating a catalogue or price list?
If the pages or the paper change, the spine changes and the cover has to be checked. If not, checking the inner pages is enough.
- Same page count and same paper: the spine does not change. Check the page numbers, the contents page and the product codes.
- More or fewer pages: a new spine width and, when saddle-stitched, a multiple of 4 again.
- A different paper: even if the weight is the same, the spine may change. Ask us.
- Prices that change more often than the catalogue: consider with us moving them into a separate price list, so you do not reprint the whole catalogue every time they are updated.
9. What are the most common mistakes?
| Mistake | What happens | How to avoid it |
|---|---|---|
| A saddle-stitched job whose page count is not a multiple of 4 | It cannot be made up: there are blank pages too many or too few | Fit the content to 8, 12, 16, 20… |
| PDF exported as spreads or imposed sheets | The pages have to be separated before printing and the bleed in the centre is lost | Export as single pages, in reading order |
| Inside margin the same as the outside margin with PUR or sewn binding | Text and tables end up buried in the spine | A wider inside margin, wider still the more pages there are |
| Text or a table crossing the centre of a spread | Part of it is lost in the spine or cut by the loop | Keep the centre free of text and data |
| Cover finalised before the spine is known | The spine title ends up off-centre or runs onto the front cover | Ask us for the width before finalising the cover |
| Cover with spine in the same PDF as the inner pages | It has to be separated and the page order checked again | Two PDFs: inner pages and cover |
| Blank pages removed from the PDF | The order and page numbers do not match the final catalogue | Leave blank pages in their place |
| Page numbers right at the trim line or next to the spine | They get trimmed off or hidden | 3-5 mm from the trim line, preferably on the outer side |
Frequently asked questions
Why does a saddle-stitched catalogue need a multiple of 4 pages?
Because each sheet is folded in half and gives four pages. With 30 pages of content, the catalogue comes out at 28 or 32: any missing pages are filled with blank pages.
Which binding stays open and flat on the table?
Wire-o: it opens fully and can be folded back on itself. That is why it is used for reference catalogues, manuals and price lists that are used at a counter or next to the computer.
Can I put the catalogue's name on the spine?
Yes, with PUR, sewn, concealed wire-o or hardcover binding, if the spine is wide enough for the text to be readable. Ask us for the width before designing it.
Should I send the PDF as spreads so you can see how it looks?
Not for production: the inner pages go as single pages. If you want us to see how the spreads work, you can also send us a PDF in spreads for reference only.
When is PUR binding better than saddle stitching?
When the catalogue has many pages or the paper is thick: staples no longer close it properly, and PUR binding gives a sturdier finish and a spine that can carry a title. Tell us how many pages it has and we will tell you what fits.
What happens if my file does not meet these conditions?
Before production, we check its technical specifications. If something is missing, such as the page count, the inside margin or the spine, we tell you what is missing and work out with you how to fix it.