Black and brand colours are what changes most between screen and paper. A file handles them properly when it meets these conditions:
- Text, fine lines and small black logos are in black only: K 100%.
- Large black areas are in rich black: C 60 M 60 Y 60 K 100.
- Black that comes from an RGB file or a screen logo gets checked: when converted to CMYK it turns into a four-ink black.
- Colours are converted to CMYK before sending, with the ISO Coated v2 or FOGRA51 profile, and checked.
- A Pantone is only left as a spot colour if the job is going to be printed with that ink. If not, it is changed to CMYK using the value from the brand guidelines.
- The same colour on different papers and materials comes close, but is not identical. If it is critical, ask for a proof.
- The “Barniz” (varnish) or “Stamping” (foil stamping) inks are not Pantones: they are instructions for the finish and must be left alone.
Colour profiles, CMYK conversion and PDF/X are covered in the guide How to prepare a file for printing. Here we explain why black and corporate colours need special care and how to check them.
1. Which black should I use for text?
Black only: K 100%, with no cyan, magenta or yellow. This applies to text, fine lines, tables, barcodes and QR codes, and small black logos.
What happens if not. In a built black, each ink is printed separately and there is always a slight registration error between them. On a small letter, that error lets the cyan or magenta show through: the letter seems to have a colour shadow and is hard to read. A barcode or QR code may not scan. With K 100% there is only one ink and nothing to misregister.
Watch out: on screen, text in K 100% and text in four-ink black look identical. You can only tell them apart by checking the colour values or the separations (section 10).
2. Which black should I use for a large black background?
Rich black: C 60 M 60 Y 60 K 100. Over a large area, black on its own comes out greyish and dull; the other three inks underneath give it depth.
- Where to use it: black backgrounds, dark covers, black bands and blocks.
- Where not to: on small text and fine lines, because of the same registration problem as in section 1.
- One rich black throughout the piece. If two different blacks share the same background (one rich and one K only, or two different mixes), the difference in tone shows when printed even if they look the same on screen.
- Do not use the “Registration” colour. Design software includes it for crop marks: it puts every ink at maximum. On a background or text, it lays down far too much ink (section 8).
For anything in between, such as a very large headline or a medium-sized black logo, check with us before you finalise the design.
If there is text reversed out in white on that black background, use regular or heavier weights: the surrounding ink tends to fill in fine strokes. We explain this in the colour section of the file preparation guide.
3. What happens to the black in an RGB file or a screen logo?
When converted to CMYK it stops being pure black and turns into a four-ink black. Screen black does not exist in print: the conversion translates it into a mix of cyan, magenta, yellow and black.
It happens with text written in Word or PowerPoint, with logos copied from a website, with brand guideline PNGs intended for screen and, in general, with any design that starts out in RGB and is converted to CMYK on export.
- In text: the result is the one in section 1, letters with colour halos.
- In backgrounds: you get a different mix from the recommended rich black. If it sits alongside other blacks, the difference shows.
What to do. After converting to CMYK, select the black text and check its values. If it contains all four inks, assign it the K 100% black swatch. For the logo, ask for the CMYK vector version from the brand guidelines, or the single-colour black version if there is one.
4. What is black overprinting and when should I use it?
It means printing black on top of the background colour, without knocking out the background underneath. It is recommended for black text and lines on coloured backgrounds.
By default, when text sits on a background, the software knocks out the background in the shape of the letters (a “knockout”) and the text fills that gap. If the registration shifts slightly, a thin white line shows between the letter and the background. If the black overprints, the background stays whole underneath and no gap can appear. Because black covers, the colour underneath is barely noticeable.
- Only with K 100% black. A grey or a light colour set to overprint mixes with the background and changes tone.
- Never with white. White text or a white logo set to overprint disappears when printed, because white is not an ink: it is the unprinted paper.
- Some software already overprints 100% black by default. InDesign does this with its black swatch (controlled in the preferences, under Appearance of Black). If you use a different black or define your own swatch, check it.
To turn it on manually in Illustrator or InDesign, select the object and tick Overprint Fill in Window → Attributes (in InDesign, Window → Output → Attributes). Overprinting for finishes works the same way; we explain it in the varnish and foil stamping guide.
5. Why do screen colours change when printed in CMYK?
Because four inks cannot reproduce every colour a screen can show. Electric blues, very saturated greens and oranges, and intense pinks dull when converted to CMYK. It cannot be avoided, but it can be controlled:
- Convert it yourself before sending, with the ISO Coated v2 or FOGRA51 profile, so you can see the result and adjust it. We explain this in the file preparation guide.
- If a brand colour has gone dull, adjust it with the CMYK values from the guidelines instead of leaving the automatic result.
- If the colour is critical, ask for a proof before the print run. The screen is no reference: each one shows colour in its own way.
6. Pantone or CMYK: which should I use?
CMYK, unless the job is going to be printed with that Pantone ink. Most presses on the market print in four-colour process, and almost every job is printed that way, corporate colours included. Printing with a Pantone spot colour is a speciality: in offset it means an additional ink, and on short or medium print runs it rarely pays off.
What happens if you leave the Pantone in a CMYK job. The colour is converted to four-colour process automatically, and the result may not match what your brand guidelines expect. Also, if the same Pantone appears under two different names (for example, its coated and uncoated versions), the file has two inks where there should be one.
What to do:
- Look up the CMYK value in the brand guidelines. Almost all guidelines give, for each colour, its Pantone, its CMYK and its screen value. Use the CMYK.
- Change the swatch, not the result. Edit the Pantone swatch in the document and turn it into a CMYK swatch with the values from the guidelines. That way every object using it changes at once, and the finishing inks stay untouched (section 9).
- If the guidelines do not give a CMYK value, or your guidelines require an exact Pantone, let us know and we will assess whether a spot colour is needed or a good CMYK simulation will do.
Some Pantone colours are beyond the reach of four-colour process: certain very saturated oranges, greens and blues, plus metallics and fluorescents. If your brand colour is one of them, it is worth knowing before you design.
7. Will my corporate colour look the same on every piece?
Very similar, but not identical. With the same CMYK values, colour changes depending on the paper, the printing system and the material.
| Material | How the colour changes |
|---|---|
| Coated paper (gloss or matt) | The ink stays on the surface: brighter, sharper colours |
| Uncoated paper (offset, the kind used for letterheads) | The paper absorbs more ink: duller, slightly darker colours |
| Coloured or kraft papers | The colour of the paper mixes with the colour of the ink |
| Lamination (gloss, matt, soft touch) | Gloss brightens the colour; matt and soft touch soften it |
| Large format (PVC banner, vinyl, fabric) | Different inks and materials: the colour comes close, but does not match the paper |
What helps them look as alike as possible:
- Always using the same CMYK values from the guidelines on every piece, without tweaking them by eye in each design.
- Telling us which colours are critical when you order: the logo colour is not the same as a secondary colour.
- Having a reference piece, printed and approved, and comparing against it.
- Asking for a proof when colour is decisive, especially on uncoated papers and in large format.
If your brand has pieces on several materials and you want them to look consistent, tell us before you start and we will work out the material for each one with you.
8. How much ink can a dark colour carry?
Less than the software allows. The total of the four inks at any one point has a limit: if it is exceeded, the ink takes longer to dry, can set off onto the sheet on top and cracks at the folds.
- The recommended rich black is already designed for this. Do not load it further or put all four inks at maximum.
- When converting with the recommended profile, the profile itself limits the total ink of the converted images and colours. Colours you define by hand, however, do not go through that limit.
- Browns, navy blues and very dark greens built with a lot of each ink are the ones that most often go over.
If your design has large dark areas made with your own mixes, especially on uncoated paper or on a piece that folds, check with us before you finalise it.
9. Are the “Barniz”, “Stamping” or “Blanco” inks Pantones?
No. They are spot colours, like a Pantone, but they are not design colours: they are instructions showing where a finish or a special ink goes. They are never converted to CMYK and they are set to overprint.
That is why the rule in section 6 does not apply to them: a Pantone in the design is changed to CMYK; “Barniz”, “Stamping” or “Blanco” (white) are left as they are. If you convert all spot colours to process when exporting, the finish is printed as just another colour.
We explain how to prepare those layers in the guides on varnish and foil stamping and special inks.
10. How do I check blacks and colours before sending?
With the separations preview: it shows each ink separately and lets you see which black each object uses and which spot colours are in the file.
- In the PDF, with Acrobat: open Output Preview. Turn off cyan, magenta and yellow: black text should still be fully visible. If it disappears or loses part of itself, it is not in K 100%.
- In InDesign: Window → Output → Separations Preview does the same check, and the Ink Manager lists the inks in the document.
- In Illustrator: Window → Separations Preview, with Overprint Preview turned on to see how anything set to overprint will look.
- The ink list should show only cyan, magenta, yellow and black, plus the finishing inks if the piece has them (“Barniz”, “Stamping”, “Blanco”). A Pantone in that list, in a four-colour job, is a warning sign.
11. What are the most common mistakes?
| Mistake | What happens | How to avoid it |
|---|---|---|
| Small text in four-ink black | Colour halos around the letters | Text and fine lines in K 100% only |
| Large black background in K only | Comes out greyish and dull | Rich black C 60 M 60 Y 60 K 100 |
| Black text or logo from RGB | Turns into four-ink black without it showing on screen | Check the values after converting and assign K 100% |
| “Registration” colour in the design | Too much ink: slow drying and set-off | Keep it for crop marks |
| White set to overprint | The white text or logo disappears | Overprint only K 100% black and finishes |
| Pantone in a four-colour job | It is converted automatically and the colour may change | Change the swatch to CMYK with the value from the brand guidelines |
| The same Pantone under two names | Two inks where there should be one | Check the Ink Manager before exporting |
| Converting all spot colours on export | The varnish or foil prints as a colour | Convert only the Pantone swatches in the design |
| Expecting the same colour on paper and on a PVC banner | Differences between pieces from the same brand | Same CMYK values, a reference piece and a proof if it is critical |
Frequently asked questions
Why has my black background come out greyish?
Almost always because it was in K 100% black only. Large areas need rich black, C 60 M 60 Y 60 K 100, to come out deep.
Can I use my website's colour code for printing?
Not directly. The website code is a screen colour (RGB) and it may change when converted to CMYK. Use the CMYK value from the brand guidelines; if you do not have it, convert the colour, check it and, if it is critical, ask for a proof.
My brand guidelines only give a Pantone. What should I do?
Let us know when you order. We will assess with you whether it needs printing with a spot colour or a good CMYK simulation will do, and with which values.
Do I need to do anything about overprinting if my text is already in K 100%?
In InDesign, usually not: it overprints its black swatch by default. In other software, check it (section 4). In every case, it is worth checking in the separations preview that nothing white or coloured has been set to overprint by mistake.
What if my file does not meet all of this?
We check its technical specifications before production. If there is text in four-ink black, unconverted Pantones or extra inks, we tell you what is missing and work out with you how to fix it.