A folded leaflet is ready for print when the file meets these conditions:
- It is a two-page PDF at the open size: page 1 is the outside (what you see with the leaflet closed) and page 2 is the inside.
- The panels have the sizes for their fold. On an A4 roll-fold tri-fold: 100, 100 and 97 mm; the 97 mm panel is the one that folds in.
- The reverse is turned the right way: left to right if the folds are vertical; if they are horizontal, one side is upside down relative to the other.
- Text and logos sit 3-5 mm from the folds, just as from the trim. Finishes, at least 3 mm.
- From 170 gsm the paper is creased before folding; below that, it is folded directly. If there is heavy ink or solid backgrounds over the fold, it is laminated as well.
- Before sending it, you have made a paper mock-up and checked that every face lands in the right place and the right way up.
Everything else is as for any printed item: 3 mm of bleed with crop marks, CMYK, resolution and fonts. That is covered in the guide How to prepare a file for printing. Here we explain only what changes when the piece is folded.
1. What types of fold are there and how many faces does each have?
Each fold is defined by the number of folds and by how the panels close. Each panel has two faces: one on the outside and one on the inside. A bi-fold has 4 faces; a tri-fold, 6; a four-panel leaflet, 8.
| Fold type | Folds | Faces | How it closes | What it is for |
|---|---|---|---|---|
| Bi-fold | 1, in the centre | 4 | Folded in half, like a book | Short presentations, invitations, menus, programmes |
| Roll-fold tri-fold | 2 | 6 | One panel folds in and the other wraps around it | The most common sales leaflet: front cover, three faces of content and back cover |
| Concertina | 2 | 6 | Zigzag: each fold goes the opposite way to the one before | Content read in sequence: steps, routes, product ranges |
| Gate fold | 2 | 6 | The two side panels close towards the centre, like two doors | Presenting a product or an image that is revealed on opening |
| Roll fold with 3 folds | 3 | 8 | The panels roll up one inside the other | More content at the same closed size as a tri-fold |
| Double gate fold | 3 | 8 | The side panels close towards the centre and then it is folded in half | Product leaflets that open out to a large surface |
| Cross fold | 2, at right angles | 8 | Folded in half and then in half again the other way | Maps, plans and posters that have to fit into a small format |
The roll-fold tri-fold and the concertina are often confused, but the file for one does not work for the other: the panel sizes and the order of the faces change.
If your leaflet also has a die-cut shape (a rounded corner, a cut-out window), the cut is prepared as we explain in the die-cutting guide.
2. Where does page 1 go and in what order do the faces go?
Page 1 of the PDF is the outside: all the faces you see with the leaflet closed, including the front and back covers. Page 2 is the inside: what you see when it is fully open.
You do not send one page per panel. Unlike a catalogue, which is supplied as single pages, each page of a folded leaflet's PDF is the whole sheet, open, with the panels side by side.
Bi-fold
On page 1, the back cover goes on the left and the front cover on the right. Page 2 has the two inside faces, which read from left to right like an open book.
Roll-fold tri-fold
From left to right, as seen on screen:
| PDF page | Left panel | Centre panel | Right panel |
|---|---|---|---|
| 1 · Outside | The panel that folds in (97 mm): the first thing you see when you open the front cover | Back cover (100 mm) | Front cover (100 mm) |
| 2 · Inside | Inside left (100 mm) | Inside centre (100 mm) | Inside of the fold-in panel (97 mm) |
Notice that the 97 mm panel is on the left on the outside and on the right on the inside: it is the same panel seen from both faces. If you put it on the same side on both pages, the leaflet will not close properly.
Concertina
The front cover is one of the end panels and the back cover is the panel at the other end, on the other side. Which one depends on the direction you want it to open: decide with the mock-up (section 7).
3. How is the reverse turned depending on the fold direction?
If the folds are vertical, the reverse turns from left to right, like the page of a book, and both sides of the PDF run the same way. If they are horizontal, one side is upside down relative to the other.
- Vertical folds (panels side by side: standard bi-folds, tri-folds and concertinas). Both pages of the PDF are the right way up. When you turn the sheet over, what was on the left on the outside ends up on the right on the inside; that is why the 97 mm panel of the tri-fold changes sides.
- Horizontal folds (panels one above the other, like a tent card or a bi-fold that opens upwards). The sheet turns from top to bottom, and one side is upside down relative to the other. On a tent card, in addition, the two outside faces run in opposite directions within the same page, so that they read the right way up from both sides of the table.
The orientation of each face is a design decision, and the file is the reference: if a face arrives rotated, it prints rotated. With horizontal folds and cross folds, a paper mock-up is the only reliable way to check it.
4. What size is each panel?
It depends on the fold. On a bi-fold, the two halves are equal; on a concertina, all the panels are the same size; on a roll-fold tri-fold, the panel that folds in is narrower.
| Fold type | Open size | Panels, left to right on the outside |
|---|---|---|
| Roll-fold tri-fold | A4 landscape (297 × 210 mm) | 97 + 100 + 100 mm (on the inside, 100 + 100 + 97 mm) |
| 3-panel concertina | A4 landscape (297 × 210 mm) | 99 + 99 + 99 mm |
| Bi-fold | Any size you choose | Two equal halves |
Why is the inside panel of the tri-fold narrower? Because it sits inside the other two. If it were the same width, it would hit the fold when closing: the leaflet would bulge or the panel would buckle at the edge.
For other formats or folds (gate fold, double gate fold, roll fold with 3 folds, cross fold), ask us for the sizes before you start the design. There are no generic templates that work for all of them: the inside panels depend on the fold and the paper.
How to set it up in your software
- Create a document at the open size (for example, 297 × 210 mm) with two pages and 3 mm of bleed all round.
- Place guides at each fold, at the exact distance from the left edge. On the roll-fold tri-fold, on the outside: at 97 and 197 mm; on the inside: at 100 and 200 mm.
- Folds have no bleed. Bleed goes only around the sheet, on the edge that is trimmed. Between one panel and the next, the design is continuous.
- Do not draw fold lines or panel frames in the file: they would print. Guides in your software do not appear in the PDF.
Example. An A4 roll-fold tri-fold set up with three 99 mm panels looks right on screen. When folded, the inside panel hits the fold and pushes outwards, and the leaflet does not close flat. With 100, 100 and 97 mm it closes cleanly.
5. How far should text be from the folds?
The same as from the trim: text, logos, numbers and QR codes, 3-5 mm from each fold. A fold, like a trim, never falls exactly on the theoretical line, and anything right next to it can end up folded or slip onto the next panel.
- Text and key elements: 3-5 mm from the fold, on each side. No line of text should cross a fold.
- Varnish, foil stamping and other finishes: at least 3 mm from the fold and the crease. When folded, they crack or flake off. We explain this in the spot UV varnish and foil stamping guide.
- Photos and backgrounds can cross a fold. Avoid having the fold run through a face, a product or text within the image.
- Fold types with 3 or more folds (double gate fold, cross fold, roll fold with 3 folds): leave a little more margin next to the folds. The more folds there are, the more any small deviation adds up.
6. When is creasing needed and when is lamination needed?
From 170 gsm, the paper is creased before folding; below 170 gsm it is folded directly, without creasing. If there is also heavy ink or a solid background over the fold, lamination is advisable.
- What creasing is. A pressure mark along the fold line that prepares the paper to bend. Without it, on heavy paper the fibres break on the outside of the fold and the edge cracks.
- From 170 gsm, always. Below 170 gsm there is no creasing: the paper is folded directly.
- Heavy ink on the fold: lamination. With solid or dark backgrounds or heavy ink coverage over the fold, the ink cracks when folded and can set off onto the opposite face. Lamination protects it. The types of lamination are in Finishes.
Example. A bi-fold on heavy board with a navy blue outside printed to bleed: without creasing, the spine cracks and shows the white of the paper; with creasing but no lamination, the ink on the spine can crack. With creasing and lamination, the fold comes out clean.
Do I need to mark the crease in the file?
For standard folds, no: the folds follow from the fold type and the panel sizes you give us when you order. You only need to mark it if the crease is not obvious, for example on a piece with a special shape or with folds outside the usual sizes. In that case:
- Create a layer called “Hendido” (crease) and a spot colour with the same name.
- Draw each crease as a vector line at 100 % of that spot colour, set to overprint. No gradients, transparency or screens.
- If the piece also has a die-cut outline, it goes on a separate layer, “Corte” (cut). We explain this in the die-cutting guide.
7. How do I make a paper mock-up to check it?
Print both pages of the PDF at 100 %, one on each side of the same sheet of paper, trim it and fold it. In a few minutes you can see whether each face lands in the right place and the right way up, something that is easy to miss on screen.
- Print the PDF at actual size, without “Fit to page”, double-sided. If your printer cannot print double-sided, print both pages and glue them back to back.
- Trim along the trim line and fold along the guides, in the order of the fold you are going to order.
- Check: the front cover is on the front with the leaflet closed; no text is upside down; nothing important falls on a fold; the inside panel of the tri-fold does not catch when closing.
8. What are the most common mistakes?
| Mistake | What happens | How to avoid it |
|---|---|---|
| Three equal panels on a roll-fold tri-fold | The inside panel hits the fold and the leaflet does not close flat | On A4: 100, 100 and 97 mm |
| The narrow panel on the same side on both pages | Outside and inside do not line up when folded | Outside: 97 on the left; inside: 97 on the right |
| Front cover on page 2 or on the wrong panel | With the leaflet closed you see the inside or the back cover | Page 1 = outside; on the tri-fold, the front cover is the right-hand panel |
| One PDF page per panel | The sheet has to be reassembled and continuity between panels is lost | Two pages at the open size: outside and inside |
| Reverse turned the wrong way on a horizontal fold | One side prints upside down | A paper mock-up before sending |
| Text right up against the fold | It ends up folded or slips onto the next panel | 3-5 mm on each side of the fold |
| Fold lines or panel frames drawn into the design | They print | Software guides, which do not appear in the PDF |
| Paper of 170 gsm or more without creasing | The fold cracks | Creasing from 170 gsm |
| Solid background over the fold without lamination | The ink cracks and can set off onto the other side | Lamination, or a design with less ink on the fold |
Frequently asked questions
What is the difference between a bi-fold, a tri-fold and a four-panel leaflet?
The number of panels. A bi-fold has 2 panels and 4 faces; a tri-fold, 3 panels and 6 faces; a four-panel leaflet, 4 panels and 8 faces. Within each, the fold type (roll fold, concertina, gate fold, double gate fold…) changes the sizes and the order of the faces.
Do folds need bleed?
No. The 3 mm bleed goes only around the open sheet, where it is trimmed. At the folds, the design runs continuously from one panel to the next.
Can I order a fold with different sizes?
Yes. Ask us for the panel sizes for your format and fold before you start the design. That way the file is right first time.
Can a photo run across a fold?
Yes, backgrounds and photos can cross the folds. Make sure the fold does not fall on a face, a product or text, and if the background is very dark and the paper heavy, have it laminated.
Can I print a folded leaflet on kraft or textured paper?
Check with us before you finalise the design. On textured papers, flat backgrounds do not print evenly. And on coloured papers, such as kraft, the colours in the design change unless they have white underneath; we explain this in the special inks guide.
What happens if the panels in my file are not the right size?
Before production we check its technical specifications. If the panels, the order of the faces or the margins do not fit the fold, we tell you what is missing and work out with you how to fix it.